Prototyping in your Home-Office
Survival-Kits for electronic technicians at home

Do you also want to develop within the HomeOffice and need to solder THT components to your PCB?
This is exactly why we created this Home Office THT Kit for you.
It consists of:

1x ERSA soldering station i-Con pico,
1x ISO Core solder wire 0.5 mm 100 g,
1x Component lead bending tool, 1x Helping hand with magnifying glass  and 1x Palux 30H fluid set (50ml).

Information about ERSA soldering station i-Con pico

The i-CON pico is the ideal soldering station for users who expect professional quality results. It offers the beginner all the functions that are also valued in industrial manufacturing, such as very fast heat-up and heat recovery, stand-by function and calibration mode. Using the software and an optional micro SD card further settings are available to increase the operational reliability. A wide range of standard soldering tips of the series 102 is available for the i-Tool pico.
The i-CON pico can be combined with the mini solder bath i-Solder-Pot which is available in our shop.
Caution: this only applies to mini solder baths that require a heating element.

Type of control: i-TRONIC control
Antistatic: no
Nominal voltage: 230 V
Secondary voltage: 16.5 V
Power rating of control station: max. 80 W
Power rating of soldering iron: max. 80 W
Temperature range: 150 °C - 450 °C
Preheating time: approx. 9 sec
Station soldering iron: Soldering iron i-Tool pico
Weight without power cord (iron): 30 g
Tip alloy: ERSADUR LF
Soldering tip type (iron): 0102CDLF16

Soldering tip series: ERSA soldering tip series 0102
Standby: Yes
Calibration: Yes
Iron holder Tool holder: 0A53
RoHS: RoHS-compliant

Information about solder wire ISO Core"Clear"

The “Clear“ flux formula is based on synthetic resins (free of colophonium), and it has been perfectly matched with the new requirements concerning lead-free soldering technologies:
• High wetting rate and spread on all common surfaces used in electronics
• No (painful) flux splashed on the component, system parts or the user’s hands
• Transparent flux residues to optimize the optical impression
• Very low gas emission levels and neutral odour to reduce workplace pollution
• 100 MΩ test passed - can also be used in assembly production
• The soldering tip service life is considerably lengthened
Lead-free soft solder wire filled with flux
Flux residues in compliance with DIN EN 61190-1-3 • REL1
High-qualification solder wire for manual and robot soldering in electrical engineering, electromechanics and electronics.
Standard flux content 3.5%
Thermally stable - non-splash - optimum wetting - transparent residues

Solder wire diameter: 0.5 mm
Package size: 100 g coil

Information about Palux 30H fluid set (50ml)

Palux 30H is highly suitable for all printed circuit boards (also SMD).
The fluid is soluble in water and non-foaming.
It can be rinsed off in cold water and guarantees low levels of ionic impurities.
The surface of the printed circuit board after tin plating is shiny and has excellent electrical surface resistances.
Palux 30H is neutral to stainless steel, solder baths and soldering tips. Cover panels and exhaust air systems are not damaged by the fluid and are thus easy to care for.
When introducing rinsing water into the waste water channels, the local regulations must be observed. The safety data sheet is available in the Download area.
Even corroded pads and bare copper can be soldered without difficulty.
The connections on THT components can be carefully wetted with the fluid before soldering.
The soldering quality when using a hand-held soldering iron or our solder pots is remarkable.
The kit includes a 50 ml wide-neck container with fluid and a 4-mm wide brush that you can use to wet the pads or the pins on the components. We recommend that you refill it with Palux 30H fluid 250 ml. Replacement brushes are also available.

Technical data:

pH in a water solution: approx. 1
Viscosity: approx. 350 mm
2/sec Density: 1.07 – 1.1 g/cm3
Flash point: > 300°C
Ignition temperature: approx. 415°C

CAUTION: Avoid contact with skin, use protective gloves and protective glasses.

- Similar to illustrations -
Item number: RK-11005
Availability: immediately
Gross: 196.00 GBP
Net: 159.35 GBP

plus shipping costs

Order quantity: